0.75 Cubic Concrete Mixer-manufacture,factory,supplier from China

This portable concrete/mortar mixer is equipped with wheels and traction tongue, so it can be pulled by motor vehicles and moved around the construction site by hand, and its rotation is powered by mains power. Xxx Allow concrete/mortar to be dumped into the wheelbarrow. An outdated model of a small concrete mixer. These old mixers are too heavy to move easily. They are still self powered by electric motors.For smaller jobs, such as home repairs, renovations, or amateur scale projects, many cubic yards of concrete are usually not required.

First. Handling of dustFrom the main station to the backyard dust to be solved, the main station adopts high efficiency pulse back-blowing active dust removal, plus large lantern dust removal, installation of mainstream fans to keep the air in the station fresh, powder tank using bin top dust removal and ground centralized dust collection, can also be concentrated on the batching layer platform dust collection, through the screw conveyor to the powder weighing, mixing station using pressurized spray unloading water to reduce the amount of dust in the mixer, the backyard encapsulated above

To prevent concrete mixer leakage, you could take the following steps:1. Regular protection: make sure to clean the mixer after every use, investigate and update any tired parts, tighten any free bolts, and lubricate the shifting parts.2. Use exquisite substances: use extremely good cement, sand, gravel, and water to make sure the concrete mix is homogeneous and that it flows easily thru the mixer.3. Avoid overloading the mixer: do now not overload the mixer past its capacity, as this could reason the mixer to leak.

There are several ways to prevent concrete mixer leakage:Check the seals: regularly check the seals of the concrete mixer, including the mixer dust sealing device, feeding system sealing device, discharge door sealing device and so on. Make sure the seals are in good condition and have no problems such as aging, wear or cracks.Clean the concrete residue: after each mixing of concrete, the interior and exterior of the concrete mixer should be cleaned in time.

The hazards of concrete mixer holding shaft1. Affect the quality of concrete, the mixer holding the shaft after hitting the concrete mixing is not uniform.2. Increase the load of the concrete mixer, energy consumption increases.3. Affect the wear parts, shaft seal life, accelerate the wear of wear parts, hold the shaft after the mixer arm wear is very serious, the service life is greatly shortened.Methods to prevent the mixer from holding the shaft1.

Here are the steps to smooth a concrete mixer:1. Turn off the mixer: earlier than cleansing the concrete mixer, flip off the gadget and unplug it from the strength supply.2. Dispose of the cement: use a spade or shovel to do away with any last cement from the mixer. make sure to put on gloves and goggles to protect yourself from the cement dirt.3. Wash out the drum: fill the mixer with water to approximately halfway and flip it on. let it run for a couple of minutes to thoroughly wash out the drum. then, turn off the mixer and drain the water.4.

There are several factors that affect the efficiency of concrete mixing plant:  Equipment status and performance: the equipment of the concrete mixing plant includes mixer, weighing system, conveying equipment, etc. The good status and performance of the equipment are the key factors to ensure the production efficiency. Equipment maintenance and timely repair of faults can ensure normal operation and efficient production.  Raw material supply and quality: the raw materials of concrete mixing plant include cement, aggregate, sand, etc.

Advanced mixing concept, can reduce the load of mixing, reduce the phenomenon of keeping shaft of substances, three-dimensional operation trajectory can lessen the strength consumption of equipment, quickly entire the work.The materials to be combined by way of the double horizontal shaft concrete mixer are focused inside the relative attention between the two shafts and interlocked to supply mutual friction inside the barrel and increase the frequency of motion to attain the required blending of substances.

Features of JS double horizontal shaft concrete mixer1. Compact structure: JS double horizontal shaft concrete mixer adopts vertical structure, covers a small area and has a compact structure.2. Uniform mixing: The equipment adopts double horizontal shaft design, which can mix various concrete ingredients quickly and evenly, ensuring stable and reliable concrete quality.3. Stable performance: JS double horizontal shaft concrete mixer adopts high-quality hydraulic and electrical components, stable performance and long service life.4.

The 500 mixer that we usually refer to is the JS500 concrete mixer, which belongs to a kind of forced mixer. The structural design of the 500 mixer is also relatively simple, so we will mainly explain the construction details of the equipment.Mixing system  The main components of the mixing system of the 500 mixer are: mixing shaft, mixing arm, mixing cylinder, mixing blades and side blades. There are two mixing shafts installed horizontally in the mixing cylinder of the mixer, each of which has a mixing blade installed on top.