Precast Mixer Concrete-manufacture,factory,supplier from China

First. Handling of dustFrom the main station to the backyard dust to be solved, the main station adopts high efficiency pulse back-blowing active dust removal, plus large lantern dust removal, installation of mainstream fans to keep the air in the station fresh, powder tank using bin top dust removal and ground centralized dust collection, can also be concentrated on the batching layer platform dust collection, through the screw conveyor to the powder weighing, mixing station using pressurized spray unloading water to reduce the amount of dust in the mixer, the backyard encapsulated above

There are several ways to prevent concrete mixer leakage:Check the seals: regularly check the seals of the concrete mixer, including the mixer dust sealing device, feeding system sealing device, discharge door sealing device and so on. Make sure the seals are in good condition and have no problems such as aging, wear or cracks.Clean the concrete residue: after each mixing of concrete, the interior and exterior of the concrete mixer should be cleaned in time.

The hazards of concrete mixer holding shaft1. Affect the quality of concrete, the mixer holding the shaft after hitting the concrete mixing is not uniform.2. Increase the load of the concrete mixer, energy consumption increases.3. Affect the wear parts, shaft seal life, accelerate the wear of wear parts, hold the shaft after the mixer arm wear is very serious, the service life is greatly shortened.Methods to prevent the mixer from holding the shaft1.

To prevent concrete mixer leakage, you could take the following steps:1. Regular protection: make sure to clean the mixer after every use, investigate and update any tired parts, tighten any free bolts, and lubricate the shifting parts.2. Use exquisite substances: use extremely good cement, sand, gravel, and water to make sure the concrete mix is homogeneous and that it flows easily thru the mixer.3. Avoid overloading the mixer: do now not overload the mixer past its capacity, as this could reason the mixer to leak.

Here are the steps to smooth a concrete mixer:1. Turn off the mixer: earlier than cleansing the concrete mixer, flip off the gadget and unplug it from the strength supply.2. Dispose of the cement: use a spade or shovel to do away with any last cement from the mixer. make sure to put on gloves and goggles to protect yourself from the cement dirt.3. Wash out the drum: fill the mixer with water to approximately halfway and flip it on. let it run for a couple of minutes to thoroughly wash out the drum. then, turn off the mixer and drain the water.4.

Brief description of the start-up process of concrete mixing plant In a concrete mixing plant, the main mixing machine is an important part, which can be directly related to the output of the whole plant and the quality of the concrete produced. The normal start-up procedure of the mixing plant is crucial, the following is a brief introduction of how to start the mixing machine correctly.First, before starting the concrete mixer on, do a comprehensive inspection of the mixer.Second, start the mixing motor (i.e.

The 500 mixer that we usually refer to is the JS500 concrete mixer, which belongs to a kind of forced mixer. The structural design of the 500 mixer is also relatively simple, so we will mainly explain the construction details of the equipment.Mixing system  The main components of the mixing system of the 500 mixer are: mixing shaft, mixing arm, mixing cylinder, mixing blades and side blades. There are two mixing shafts installed horizontally in the mixing cylinder of the mixer, each of which has a mixing blade installed on top.

Planetary agitator is a new type of high-efficiency mixing and stirring equipment without dead point. It has a unique and novel stirring form. There are two or three multi-layer paddle agitators and 1 ~ 2 automatic scrapers in the kettle.

What equipment is generally available in a concrete mixing plantI. Mixing equipmentThat is, the general concrete mixer. At present, domestic manufacturers basically use double horizontal shaft forced concrete mixer, which has strong mixing function, uniform and rapid mixing, high productivity, and can achieve good mixing effect for dry hard, plastic and various proportion of concrete.　　Ⅱ. Weighing equipmentWeighing and batching equipment is an important piece of equipment in the concrete production process, which controls the ratio of various mixes.

1. multifunctional mixer. double horizontal shaft mixer produces convection and extrusion effect on materials, appropriate for mixing all styles of dry and hard concrete, with robust production ability, right first-class and excessive usage price with much less input.2. Advanced mixing idea, can reduce the load of mixing, reduce the phenomenon of preserving shaft of substances, 3-dimensional operation trajectory can reduce the electricity intake of machinery, speedy entire the paintings.